Cant change the Horizontal rod radius?
Hi,I have just finished my delta build and have a concave motion, in the center the z gap is 0.2mm but at the outside it is 1mm, i have read that i need to tweak the ''#define Horizontal rod radius''...
View ArticleTemperature not updating
HelloI'm using a ramps 1.3 board with a small modification of an added ad8497 that I need for my extruder.the thing is, the ad8497 is working fine (givign off 100mV @ 20°C...perfect). this is connected...
View Articlecura.
Hello every body, I read the question and comments ABOUT the version of cura that repetier was using in the Repetier Host but my problem is that I cannot access the cura from the plugin page any...
View ArticleX and Y Hit end Stop Normally But....
Hey again, still calibrating my machine. Each axis when homing, hits the end stop correctly, but then retracts about 10 percent of my printable area, then goes back to the end stop. A back and forth...
View ArticleSearching for Postprocessor for Fusion 360
Hi @All,I'am looking into using Fusion 360 as CAD/CAM tool.I have a cnc milling machine and i'am using a ArduinoDue with the Repetier-Firmware and Repetier-Host to controll it.The question is:* Is...
View ArticleStart signal not detected
Getting the message with arduino with ramps 1.4. I downloaded the latest marlin and installed. Tried all the baud rated. Update runs clean. I've tried a couple of different boards and get the same...
View ArticleHow to set X-home
I have a RepRapGuru PRUSA I3 The X-limit switch is on the right sideHome do I set Home to be the right side not the leftThaks in advanceMike
View ArticleLayer Height 0.05
Hey GuysI use Slic3r PE via Repetier Host. I was printing a small model and set layer height to 0.05 but it slicves to 0.1mm layers. How can i get it down to 0.5?
View ArticleRepetier Server on Raspberry Pi 3's
I'm trying to setup Repetier Server Pro on a Raspberry Pi 3b, but I'm having a problem connecting to printers, or even understanding my USB device list. I can generate a list of attached USB devices...
View ArticleAnycubic Chiron
I am unable to connect my Anycubic Chiron printer to Host. The connection appears to be made but no start signal is detected and a forced start is issued but I have no control over anything after...
View ArticlePan button?
I am running Repetier Host on a Windows 8 tablet. It seems the only way to pan around the 3D view, is to plugin a mouse with a middle button. There is a button in the program to change to rotate and...
View Articleconnect to anet a8 (prusa i3?)
I can connect cura and print objects via the usb port but I would like to use Repetier to send info.I am using windows7 on a pc connected with a usb lead direct to the printer board . All I get on the...
View ArticleCONNEXION WIFI
BONJOUR A TOUSje viens d'achever la construction de mon imprimante DIY .L' électronique est une carte de fabrication chinoise de marque LERDGE modèle K. La connexion a REPETIER host par câble usb...
View ArticleI don't see file on SD Card in Alfawise U20
- Windows 10 _ Repetier Host V2.1.3 _ Slic3r v1.3.0I use Firmware 2.16A , slic3r with output option :[input_filename_base].gcode but it saved it :.gcoon my sdcard alfawise saw only file with .gcode how...
View ArticleClik here to view.
fatal:Heater/sensor error - M999
The heater is not heating and the following message showed:Error:Temp. raised to slow. Rise = -0.31 after 13079 msfatal:Heater/sensor error - Printer stopped and heaters disabled due to this error. Fix...
View ArticleAlfawise U30
Hi, I just bought an Alfawise U30. It is intended to be driven by Repetier-Host. I just read that for the moment, piloting is simply possible by Repetier-Server. So I have two requests: 1) do you...
View ArticlePrinter does continue printing
My printer heats up, home all the axises and goes down to the bed like it's about to start be just freezes. I tried reinstalling repitier but that didn't work. What do I do??
View ArticleClik here to view.
Is it possible to output Slic3r/CuraEngine setting through Repetier-host API?
I want to develop a plugin to access the CuraEngine/Slic3r setting. Basically, I want to output part of the setting data to a text file similar to what the "Export/Save as" button does. Could anyone...
View ArticleHost is crashing when editing object placement
Using Repetier-Host version 2.1.3 on Ubuntu 18.04I am adding 3 equal objects, and after manually placing them with the Move Object tool, then tunning their positions manually removing (truncating) the...
View ArticleClik here to view.
Model Missing Layers When Slicing
Yesterday, the model had all of its layers when slicing it. The problem was that the filament was not stocking to teach layer (just a bit). I made some chances and now today only the first or just the...
View Article