I've been using Repetier Host for nearly a year now, and have now installed it on my new tablet. However, when I trz to configure the printer, I see that it automaticatically selects the wrong printer and it also won't let me change the printer either...
↧
Repetier host won't lt me select printer
↧
BLK errors?
Keep seeing these errors in repetier host, but ussually onl in the first few layers.
11:34:54.793 : Printing layer 1 of 59
11:35:19.191 : BLK 9
11:35:26.786 : BLK 6
11:39:39.098 : BLK 9
11:39:40.496 : BLK 9
11:41:46.231 : Printing layer 2 of 59
11:41:47.952 : BLK 8
11:41:48.954 : BLK 7
11:41:54.090 : BLK 8
11:43:01.766 : BLK 8
11:44:04.493 : BLK 9
11:44:09.505 : BLK 9
11:45:10.091 : Printing layer 3 of 59
↧
↧
I recently upgraded to Repetier Host v2 and can no longer communicate with my printer
I recently upgraded from Repetier Host 1.6.2 to 2.0.1 on a Ubuntu
14.04LTS PC Desktop connected to a Makers Tool Works MendelMax 3 (via
USB). The MM3 is running Marlin Firmware that was provided by the
manufacturer.
Everything was running reasonably well before the upgrade. Since the upgrade to RH 2.0.4 I have not been able to communicate to the printer. The "Connect/Disconnect" Icon on RH switches from one to the other but it doesn't seem to be communication with the printer.
I see the following in the RH GUI and logs:nn Commands Waiting
No start signal detected - forcing start
N1 M110*34
N2 M115*36
N3 M105*36
N4 M114*35
N5 m111 s6*98
JOV?f?J?z?%iE$%?JXF?*( run on string of random looking characters...)
Communication timeout - reset send buffer block
.
.
.
A search of faq's and posts all seem point to communications configuration. I've verified that the "Printer Settings" are correct (baud rate etc.) and the MM is connected properly.
Does anyone know what the solution might be?
Thanks
Michael
↧
How to enable Heatbed?
Hey there I recently bought a Micromake D1 3d printer and it has a heat bed but I cant seem to be able to turn it on. Nowhere in the 3d printer setting is the option to heat my heat bed. I even tried on Cura with USB printing and it doesn't heat up. If anyone knows how to fix this please help. Thank you.
↧
How to disable Checksum ?
I modified the Repetier firmware a little bit, so I could send my own encrypted special gcode over serial port and run it properly. However, the same special gcode cannot be sent via Repetier Host. I guess, the codes sent via Repetier Host goes through a correction “check”. I want to override this control and sent my own special encrypted gcode via Repetier Host, how can I do this? (my code includes mostly meaningless characters)
↧
↧
How can additional Slic3r Overrides be added to Repetier-Host
How do I add additional Slic3r Overrides to the Repetier-Host slicer menu display?
↧
Startup G-code for Slic3r?
I would like to insert G-code before the typical Slic3r startup, which is shown below for my system:
M107
M190 Sxxx ; set bed temperature
M104 Sxxx ; set temperature
It appears the Slic3r's "Printer Settings, Start G-code" is listed after the above, which is not what I desire.
Currently, I edit each-and-every-one of my sliced G-code sources before printing.
Is there a way to insert some Startup G-code before the "M107" line in the default code?
It appears the Slic3r's "Printer Settings, Start G-code" is listed after the above, which is not what I desire.
Currently, I edit each-and-every-one of my sliced G-code sources before printing.
Is there a way to insert some Startup G-code before the "M107" line in the default code?
↧
Editing G-code script for manual control buttons.
When I updated to version 1.5.4 the pull down box to allow editing of the 5 scripts for the buttons on the manual control screen seems to have disappeared from the G-Code editor screen. Is it located in a different place now?
↧
How do I change the starting procedure
If it helps I´m using a Wanhao i3.
My printer starts each printing by raising Z axel about 5-10mm, then waits for the temperatur to be reached and then starts to print. Why does it do that and how can I change it?
What I want is for it to go to and stay put in home position, heat up, and extrude some filament before starting printing. This way it gets more clean for my nozzle witch otherwise often gets some melted filament stuck on it.
I use the default starting Gcode and as far as I can tell there is no instructions to raise printer head?
My printer starts each printing by raising Z axel about 5-10mm, then waits for the temperatur to be reached and then starts to print. Why does it do that and how can I change it?
What I want is for it to go to and stay put in home position, heat up, and extrude some filament before starting printing. This way it gets more clean for my nozzle witch otherwise often gets some melted filament stuck on it.
I use the default starting Gcode and as far as I can tell there is no instructions to raise printer head?
; Default start code
G28 ; Home extruder
G1 Z15 F{Z_TRAVEL_SPEED}
M107 ; Turn off fan
G90 ; Absolute positioning
M82 ; Extruder in absolute mode
{IF_BED}M190 S{BED}
; Activate all used extruder
{IF_EXT0}M104 T0 S{TEMP0}
G92 E0 ; Reset extruder position
; Wait for all used extruders to reach temperature
{IF_EXT0}M109 T0 S{TEMP0}
↧
↧
Z Controls not working
Hi, I am currently using the Repetier Host V2.0.1 and I just set up everything almost perfectly. Minus the part that the Z control isn't working. Homing works fine though.
The type of printer is a Kossel, and I am using a RAMPS 1.4 board w/Arduino Mega 2560, and I am connecting it via USB. Any help would be great. Also, Ive set my printer shape to Rostock Printer (Circular print shape) and I can see a square shaped object on the virtual bed that is hollow on the top and bottom, which is far from the center of the circle. Is this normal?
Thanks
The type of printer is a Kossel, and I am using a RAMPS 1.4 board w/Arduino Mega 2560, and I am connecting it via USB. Any help would be great. Also, Ive set my printer shape to Rostock Printer (Circular print shape) and I can see a square shaped object on the virtual bed that is hollow on the top and bottom, which is far from the center of the circle. Is this normal?
Thanks
↧
Installed on DaVinci 1.0a - Motors, Light, Headed bed will not work
Simply, how do I edit the firmware and change numbers?
Now, the long explination...
I am using the DaVinci fork of repetier from here.
I failed my first few attempts at flashing, and got the "black bars". I uninstalled/re-installed Arduino software (which I had been using for other Arduino projects for years) and then the firmware installed perfectly.
I changed the DaVinci settings, in firmware, as follows:
This post seems to have my same problem:
http://forum.repetier.com/discussion/3938/davinci-1-0a-motors-not-moving/p1
The post describes zero's in the firmware being the problem, and gives numbers to replace the zero's.
How do I access the firmware and edit the zero's?
Now, the long explination...
I am using the DaVinci fork of repetier from here.
I failed my first few attempts at flashing, and got the "black bars". I uninstalled/re-installed Arduino software (which I had been using for other Arduino projects for years) and then the firmware installed perfectly.
I changed the DaVinci settings, in firmware, as follows:
// ################## EDIT THESE SETTINGS MANUALLY ################
#define DAVINCI 1// "0" if not DAVINCI, "1" For DAVI...
#define MODEL 1//"0" for first generation (jumper JP1...
#define REPURPOSE_FAN_TO_COOL_EXTRUSIONS 0 //Setting this to 1 will repurpo...
//Warning: for DaVinci 1.0 need to add a permanent fan with power supply to cool extruder
// ################ END MANUAL SETTINGS ##########################
http://forum.repetier.com/discussion/3938/davinci-1-0a-motors-not-moving/p1
The post describes zero's in the firmware being the problem, and gives numbers to replace the zero's.
How do I access the firmware and edit the zero's?
↧
Z Axis Homed Then moves wrong up or down
Hey everyone,
New to 3d printing period, built a reprapguru V2 which has the arduino 2560 & Ramps 1.4 with marlin 1.8.3 installed. So I've been looking all around just trying to get this thing to run right and I almost have it good but I am stuck currently. Basically, after I home the Z, to which it will travel down and hit the endstop just fine, but after that if I hit the manual control to move it ether up or down using the .01, .1, 1 or 10 buttons it automatically starts to move down towards the endstop. I am not sure the exact distance but its equal to about 3 inches of travel. I was looking through the code in marlin and couldn't see anything out of the ordinary (Im new to c++ however) and there is no home offset in the eeprom settings. Also, the X and Y don't have this problem, can anyone offer a suggestion?
↧
I need to build a similar repetier host
Hi I'm trying to make my school project. I am trying to make a similar Repetier Host, Firstly I've started to learn repetier protocol,
I checked this link
I didn't fully understand for example, this part: Comparison of sizes: L1 Command 1: L2 G1 E10810.1 F1000 L3 Original size: 21 Bytes L4 Updated for errorcheck: L5 N6654 G1 E10810.1 F1000 *65 L6 Errorcheck size: 29 Bytes L7 repetier-protocol: 15 Bytes I couldn't understand how the orginal size is 21 bytes in L3 and what is *65 means, I guess it's comes from fletcers checksum but I'm not sure. What does exactly mean of this ?
↧
↧
Raspberry Pi can't see pointer
It boots up but and I can see that things are activating as the pointer goes over it, but you can't see the pointer at all. Anyone else have something like this? I can't seem to figure out a way to just use the keyboard to configure it.
↧
Wer Möchte Mir helfen
Hallo an alle Mitglieder, bin hier ein Frischling und zurzeit auf diesem Portal auch orientierungslos, besitze einen RF 1000 , einen Laptop/Windows 10/ und sehr wenig Kenntnisse in der PC Welt und kenne auch die englische Sprache nicht. Mit dem 3D Drucker habe schon gedruckt bis mein alter Laptop unwiderruflich den Geist abgegeben hat und damit auch die gesamte Einstellungen mitnahm. Habe vieles versucht aber nichts erreicht, konnte nur im einem Fall Verbindung vom Laptop zum Drucker herstellen dank einem Muster mit Gcode, möchte mir jemand dabei helfen was ich alles brauche um weiter zu kommen: Repetier Host aber welche Version, Repetier Server, Cura Engine, welchen Slicer usw. Danke für alle hinweise.
↧
printer settings; extruder speed
Helllo,
i have just created this account to ask one question, maybe somebody can help...
Why are there two input fields in the printer settings tab "printer" for the extruder speed?
I am working with the version V.1.6.2 on a windows 10 installation.
Thanks, Matten
i have just created this account to ask one question, maybe somebody can help...
Why are there two input fields in the printer settings tab "printer" for the extruder speed?
I am working with the version V.1.6.2 on a windows 10 installation.
Thanks, Matten
↧
Craftware
Moved to repetier server
↧
↧
Usint Repetier Host with Octoprint server
hi
i was just wondering the best way to use Repetier Host with an Octoprint server?
i was just wondering the best way to use Repetier Host with an Octoprint server?
↧
Issues with repetier - Error: [steps]
Hi there,
I have some issues with my new corexy printer. Software 0.92.9. Testing X and Y axes, Z axis isn't plugged in yet.
Endstop state after M119 executing:
endstops hit: x_min:L x_max:L y_min:L y_max:L z_min:H z_max:H Z-probe state:H
The problem is I can't print... I start my "dry" print - hotend temp is set to 150C. Printer is homing and then goes to the centre of table. It starts printing but few seconds later I see:
23:44:15.746 : Error: [steps]
23:44:15.746 : Resend:122
23:44:15.766 : Error: [steps]
23:44:15.767 : Resend:122
23:44:18.806 : Warning: Seems like we missed a ok, got a wait - continue sending.
23:44:18.813 : Error:expected line 122 got 128
23:44:18.815 : Resend:122
23:44:18.833 : Error: [steps]
(...)
full log with ACK turned on looks like:
18:51:51.637 : busy:heating
18:51:51.715 : T:154.15 /150 B:25.35 /0 B@:0 @:0
18:51:52.723 : T:153.58 /150 B:25.35 /0 B@:0 @:4
18:51:53.651 : busy:heating
18:51:53.731 : T:152.95 /150 B:25.35 /0 B@:0 @:34
18:51:54.739 : T:152.44 /150 B:25.35 /0 B@:0 @:46
18:51:55.666 : busy:heating
18:51:55.748 : T:151.88 /150 B:25.35 /0 B@:0 @:60
18:51:56.756 : T:151.31 /150 B:25.35 /0 B@:0 @:74
18:51:57.679 : busy:heating
18:51:57.765 : T:150.85 /150 B:25.23 /0 B@:0 @:69
18:51:58.371 : ok 40
18:51:58.371 : ok 41
18:51:58.371 : N50 M105*18
18:51:58.371 : ok 42
18:51:58.371 : ok 43
18:51:58.371 : N51 M117 ETE 52m 43s*122
18:51:58.374 : ok 44
18:51:58.374 : ok 45
18:51:58.374 : Printing layer 1 of 224
18:51:58.374 : ok 46
18:51:58.374 : ok 47
18:51:58.374 : N52 G1 X101.19 Y93.325 E3.62755 F1800*60
18:51:58.374 : N53 G1 X102.632 Y93.093 E3.72512*96
18:51:58.374 : N54 G1 X107.368 Y93.093 E4.04148*101
18:51:58.378 : ok 48
18:51:58.383 : T:150.51 /150 B:25.35 /0 B@:0 @:78
18:51:58.383 : ok 49
18:51:58.383 : ok 50
18:51:58.383 : N55 G1 X109.236 Y93.489 E4.16903*107
18:51:58.384 : T:150.51 /150 B:25.35 /0 B@:0 @:78
18:51:58.386 : Error: [steps]
18:51:58.387 : Resend:51
18:51:58.400 : ok
18:51:58.400 : Resend: N51 M117 ETE 52m 43s*122
18:51:58.400 : Resend: N52 G1 X101.19 Y93.325 E3.62755 F1800*60
18:51:58.400 : Resend: N53 G1 X102.632 Y93.093 E3.72512*96
18:51:58.400 : Resend: N54 G1 X107.368 Y93.093 E4.04148*101
18:51:58.400 : Resend: N55 G1 X109.236 Y93.489 E4.16903*107
18:51:58.405 : Error: [steps]
18:51:58.405 : Resend:51
The second problem is when I disable Z-max endstop by #define MAX_HARDWARE_ENDSTOP_Z false. EXT0 temp is -900C and of course I can't heat extruder...
Could you please assist?
Thanks,
Paweu
I have some issues with my new corexy printer. Software 0.92.9. Testing X and Y axes, Z axis isn't plugged in yet.
Endstop state after M119 executing:
endstops hit: x_min:L x_max:L y_min:L y_max:L z_min:H z_max:H Z-probe state:H
The problem is I can't print... I start my "dry" print - hotend temp is set to 150C. Printer is homing and then goes to the centre of table. It starts printing but few seconds later I see:
23:44:15.746 : Error: [steps]
23:44:15.746 : Resend:122
23:44:15.766 : Error: [steps]
23:44:15.767 : Resend:122
23:44:18.806 : Warning: Seems like we missed a ok, got a wait - continue sending.
23:44:18.813 : Error:expected line 122 got 128
23:44:18.815 : Resend:122
23:44:18.833 : Error: [steps]
(...)
full log with ACK turned on looks like:
18:51:51.637 : busy:heating
18:51:51.715 : T:154.15 /150 B:25.35 /0 B@:0 @:0
18:51:52.723 : T:153.58 /150 B:25.35 /0 B@:0 @:4
18:51:53.651 : busy:heating
18:51:53.731 : T:152.95 /150 B:25.35 /0 B@:0 @:34
18:51:54.739 : T:152.44 /150 B:25.35 /0 B@:0 @:46
18:51:55.666 : busy:heating
18:51:55.748 : T:151.88 /150 B:25.35 /0 B@:0 @:60
18:51:56.756 : T:151.31 /150 B:25.35 /0 B@:0 @:74
18:51:57.679 : busy:heating
18:51:57.765 : T:150.85 /150 B:25.23 /0 B@:0 @:69
18:51:58.371 : ok 40
18:51:58.371 : ok 41
18:51:58.371 : N50 M105*18
18:51:58.371 : ok 42
18:51:58.371 : ok 43
18:51:58.371 : N51 M117 ETE 52m 43s*122
18:51:58.374 : ok 44
18:51:58.374 : ok 45
18:51:58.374 : Printing layer 1 of 224
18:51:58.374 : ok 46
18:51:58.374 : ok 47
18:51:58.374 : N52 G1 X101.19 Y93.325 E3.62755 F1800*60
18:51:58.374 : N53 G1 X102.632 Y93.093 E3.72512*96
18:51:58.374 : N54 G1 X107.368 Y93.093 E4.04148*101
18:51:58.378 : ok 48
18:51:58.383 : T:150.51 /150 B:25.35 /0 B@:0 @:78
18:51:58.383 : ok 49
18:51:58.383 : ok 50
18:51:58.383 : N55 G1 X109.236 Y93.489 E4.16903*107
18:51:58.384 : T:150.51 /150 B:25.35 /0 B@:0 @:78
18:51:58.386 : Error: [steps]
18:51:58.387 : Resend:51
18:51:58.400 : ok
18:51:58.400 : Resend: N51 M117 ETE 52m 43s*122
18:51:58.400 : Resend: N52 G1 X101.19 Y93.325 E3.62755 F1800*60
18:51:58.400 : Resend: N53 G1 X102.632 Y93.093 E3.72512*96
18:51:58.400 : Resend: N54 G1 X107.368 Y93.093 E4.04148*101
18:51:58.400 : Resend: N55 G1 X109.236 Y93.489 E4.16903*107
18:51:58.405 : Error: [steps]
18:51:58.405 : Resend:51
The second problem is when I disable Z-max endstop by #define MAX_HARDWARE_ENDSTOP_Z false. EXT0 temp is -900C and of course I can't heat extruder...
Could you please assist?
Thanks,
Paweu
↧
Not displaying 3D Model preview
Hello fellow 3D printers ![:)]( ":)")
I have built myself a Rostock and am loving using Repetier. If it weren't for your dedication I probably would have abandoned a DIY printer a long time ago. I can't get over the ease of which I was able to get this printer running.
I have built myself a Rostock and am loving using Repetier. If it weren't for your dedication I probably would have abandoned a DIY printer a long time ago. I can't get over the ease of which I was able to get this printer running.
Anyhow, I can't get 3D model previews to show in Repetier Host. The only way I can determine the orientation of a model is if I slice and view the preview.
When I first fired up Repetier, the tablet model was present but since then it hasn't shown.
When I first fired up Repetier, the tablet model was present but since then it hasn't shown.
Any help solving this issue would be appreciated.
Ps. if it helps, video drivers are up to date as is windows 8.1 and things like chipset drivers.
Thanks in advance.
↧