I am receiving an "Error:to retract when heating [mm]" when I start print after the extruder and the bed warms and the extruder moves into position to start to print. No filament is extruded before the error is received.
10:10:55.720 : N450 M105*38
10:10:55.720 : N450 M105*38
10:10:58.787 : N451 M105*39
10:11:01.845 : N452 M105*36
10:11:04.911 : N453 M105*37
10:11:07.077 : N454 G28*22
10:11:07.078 : N455 G1 Z15 F100*5
10:11:07.079 : N456 M107*34
10:11:07.079 : N457 G90*22
10:11:07.079 : N458 M82*16
10:11:07.079 : N459 M190 S50*85
10:11:07.081 : N460 M104 T0 S210*32
10:11:07.081 : N461 G92 E0*68
10:11:07.081 : N462 M109 T0 S210*47
10:11:07.081 : N463 M107*36
10:11:07.081 : N464 G0 X83.9 Y83.9 Z0.3 F9000*22
10:11:11.044 : X:-38.00 Y:-7.00 Z:0.000 E:0.0000
10:11:11.044 : N465 M117 ETE 13m 25s*76
10:11:11.044 : N466 M105*35
10:11:11.047 : Printing layer 1 of 125
10:11:11.047 : N467 G1 X96.1 Y83.9 E0.58964 F1800*2
10:12:49.169 : N468 M117 ETE 13m 25s*65
10:12:49.172 : N469 M105*44
10:14:24.714 : N470 M117 ETE 13m 25s*72
10:14:24.714 : N471 M105*37
10:14:24.716 : N472 G1 X96.1 Y88.9 E0.8313*93
10:14:24.749 : Error:to retract when heating [mm]
10:14:24.750 : N473 G1 X101.1 Y88.9 E1.07295*82
10:14:24.760 : Resend: N468 M117 ETE 13m 25s*65
10:14:24.760 : Resend: N469 M105*44
10:14:24.760 : Resend: N470 M117 ETE 13m 25s*72
10:14:24.760 : Resend: N471 M105*37
10:14:24.760 : Resend: N472 G1 X96.1 Y88.9 E0.8313*93
10:14:24.760 : Resend: N473 G1 X101.1 Y88.9 E1.07295*82
10:14:27.991 : N474 M117 ETE 13m 25s*76
10:14:27.991 : N475 M105*33
10:14:27.992 : N476 G1 X101.1 Y93.9 E1.31461*85
10:14:27.992 : N477 G1 X106.1 Y93.9 E1.55627*81
10:14:27.992 : N478 G1 X106.1 Y98.9 E1.79792*84
10:14:27.992 : N479 G1 X111.1 Y98.9 E2.03958*85
10:14:28.000 : Error:to retract when heating [mm]
10:14:28.013 : Resend: N468 M117 ETE 13m 25s*65
10:14:28.013 : Resend: N469 M105*44
10:14:28.013 : Resend: N470 M117 ETE 13m 25s*72
10:14:28.013 : Resend: N471 M105*37
10:14:28.013 : Resend: N472 G1 X96.1 Y88.9 E0.8313*93
10:14:28.013 : Resend: N473 G1 X101.1 Y88.9 E1.07295*82
10:14:28.021 : Error:to retract when heating [mm]
This problem does not occur when running in Cura 14.06. I can manually extrude filament using the manual control. My printer is a ANet A8 with the factory extruder. Thank-you in advance.
Steve