Extruder E value integer limit
I have a large format printer and when my E values get to 100000 the extruder stops turning. If I set them to 90000 they work.
View ArticleCOREXY Z AXIS MOVING UP (WRONG WAY) WHILE PRINTING
Hello,I have a dıy corexy printer and ı am using marlin firmware and repetier host. Manually is everything working good and right. But while it printing, z axis moving up every one layer. How can ı...
View ArticleError in slicing
Hi! I've a problem in slicing a big stl file (50 MB).I'm using Cura from Repetier. When the progress bar is complete the system report an error and no G-code is generated.The error...
View ArticleNo EEPROM reading on Host V. 2.0
Hi, I tried new version of Host on my Linux mint system but i can't read eeprom. On mega2560+ramps "Firmware eeprom configuration" in Config menù is not enabled. On arduino due+smart ramps instead menù...
View ArticleBillyboy
I am currently running Repetier-Host 1.5.5 do I have to uninstall this before I download version 2.0.0
View Articlenearly there just having problems with temp control
all the movements are now fine and the extruders work good as well its just the heating on everythingthe thermistors and hot ends are e3d chimera's and I have been told by e3d to use the ATC semitec as...
View ArticleEEPROM settings for Marlin
I'm running a MP3DP with Marlin RC8 bugfix. When I bring up the EEPROM settings I see no entries for changing the entruder rate. When I watch the saved settings log it sets it to 200, it just doesn't...
View ArticleHow to set home?
Hi all,I am using Repetier-Host V1.0.6. How do I set the coordinates of home? (The STL file I am printing needs to start a point other than 0,0,0). Thanks.
View Articlemove- migrate Repetier Host
Hi, i buy a new pc, i want move REPETIER HOST and configuraion on this new pc if i copy repetier host tom y new pc, my configuration for slicer & setting from my printer 3D is not copy!!! do you...
View ArticleClik here to view.
sliced and printed differs
Hi folks!I've been preparing to print 280*275 hull partand i discovered unusual behavior mostly on1 speed changes steeply and suddenly during straight and light curves approach.2 curves near one of the...
View ArticleRepetier-Host 2.0 interface feedback
so i'm using v2.0.0 for a while now and would like to report a minor issue regarding the new ui stylethe fan/bed/hotend buttons in the manual control panel became kind of annoying and error inducing as...
View ArticleZ probe Height versus Max. Z-probe-bed dist.
What is the difference between Z Probe Height and Max. z-probe-bed dist.? And how do I measure them. I read the Z probing page but I'm unclear and was hoping someone could help me out.Thanks, Jim
View ArticleAdding multiple objects, none is being sliced as shown in Object placement.
Hi,Like my title says, every time I either add an additional object or cloning one, when I slice them, the end result is not like is seen in the Object replacement screen. Using the Slic3r Prusa...
View ArticleTilting mechanism for dual hotend on a Delta printer
wandering if there is a simple gcode for a small servo or stepper to tilt the two hot ends placed on the effector when extruders change in gcode as new material is required/deposited...? and how to go...
View ArticleClik here to view.
Issues with Dual Extruders
I am having problems with my extruders not swapping when printing something that requires two materials. I am using Sli3er. Here is some info on how I am setting up everything:1 - I am importing 2...
View ArticleHeat bed warms up before extruder does...
When I was using Cura only & started printing, both the bed & extruder heated up at the same time. Now, with Repetier-Host, the bed heats up first then the extruder. This is really not a big...
View Articleprinting with skirt and brim
hello guys,is there a way to set where i can print the skirt with brim together? everytime i print with brim my skirt will not be printedthank you
View ArticleClik here to view.
Thermistor error, just flashed DaVinci 1.0a to Repetier
Hey everyone, I'm new to 3D printing so go slow Anyway, I just successfully flashed my DaVinci 1.0a to Repetier 0.93 and have host V2.0.1 installed. When I send a print job to the printer I get the...
View ArticleProblem starting a print
I am receiving an "Error:to retract when heating [mm]" when I start print after the extruder and the bed warms and the extruder moves into position to start to print. No filament is extruded before the...
View ArticleClik here to view.
Z-axis off.. printing stringy
Anyone have any ideas? it looks like there is a setting out of wack for the z-axis. I was printing layer 35 of 125 when I stopped the print. I just upgraded my firmware and host today. I did use the...
View Article